Friday, April 27, 2012

arc welders for the beginner - OFN Forums

First off, welcome to the forum.

Now for your questions. Although there is nothing wrong with a stich (SMAW) weld, much of this country has been welded together with them. There are now better technology that can be taken advantage of, especially if you want to get deeper into the automotive arena. SMAW really doesn't have much of a presence in the automotove field any more.

That said, what you are doing seems like it is working, however, if you really want to have your capabilities multiply and skills explode then I strongly suggest a good MIG (GMAW) welder. I also suggest a 220 volt machine vs. the smaller 110 vac machines as they have a much better capacity and just as importantly, a much higher duty cycle.

Miller and Lincoln are both fine machines and there are also others. Personally I bleed blue so it is nothing but Miller for me but that is merely my opinion. I have welded with a few of the Lincoln Power Migs and they are excellent machines as well. As much as I hate to admit it, I probably got a little better looking welds out of the Lincoln but I am sure it was an illusion.

As far as plasma cutters go, I would steer clear of Miller. We have a Miller Spectrum 2050 at work and it sucks. It goes through consumables at an alarming rate and I am not impressed with the quality in which it performs its fuctions.

Hypertherm and Thermal Dynamics are both great little plasma cutters, but in my opinion the ESAB PCM series is the one. Personally I have the ESAB PCM-875 at my home shop and it works fantastic. It has performed flawlessly over the past ten years I have owned it and never let me down. The consumable are not as expensive as the Miller and they last quite a long time.

Hope this information helps.

Mike.

Stick Welder/Fitter(April,2012)

Stick Welder/Fitter

Tradesmen International needs Welder / Fitters with a minimum 3 years experience in the commercial and industrial sectors. Work will be in Younstown, Ohio. Welders need experience with stick and should be able to work alone and fit from read blueprints. Also, you should have a working knowledge of safety as it applies to the welding and fitting trades. All welders must pass a 7018/6010 structural weld test, have a valid drivers license, pass a back ground check and a hair folical drug test. This job will give the right canidate plenty of over time and security.

Note: Please mention GetWeldingJobs.com in your cover letter when applying.

Welder's Magnet | Woodsmith Tips

This week’s video tip is from the Woodsmith Shop TV Show

Look for more woodworking videos on WoodsmithShop.com

Please wait while the video player loads...

From the Woodsmith Shop TV Show: Welder’s Magnet

Unique magnets instantly create storage.

Get a free preview of Shopnotes Magazine

Senior Production Welder Roma, Queensland, Australia ...

Roma, Queensland, Australia

Since 1919, Halliburton has been opening Worlds of Opportunity around the globe. We’re one of the world’s largest and most safety-conscious providers of oil field services. Come in and explore your future!

Performs assembly and welding processes such as GTAW, SMAW, SAW, PTAW hardfacing, Oxy-Fuel brazing and heat treatment, induction brazing and heat treatment. Follows written or verbal instructions which may include engineering specifications, blueprints, etc. Must be proficient in the majority of processes listed above. May train and direct other employees. Proficiency typically acquired through 3-5 years of related experience. This level may require certification.

'Ruthie the Welder' does her part Multimedia Healthcare | MMHC

With the arrival of Memorial Day, Veteran’s Day, Armed Forces Day and Independence each year, thoughts turn to those men and women who served in the armed forces during those times.
However, following the Japanese attack on Pearl Harbor some 70 years ago, one local woman performed her wartime duties as her husband prepared to ship overseas.
During 1942-43, Ruth White worked in the Kaiser Liberty Shipyards in Richmond, Calif. as a part of the “Rosie the Riveter” crews in the United States.
The crews were made up mostly of housewives whose husbands had shipped overseas as part of the war effort during World War II and they began to take jobs in factories, often building ships and planes for the government.
Those crews spawned a “Wendy the Welder” offshoot group based on Janet Doyle, a welder at the same shipyard as White.
“I started as a tacker and finished as a general welder and welded the seams of the ships,” White recounted recently as she discussed her contribution.
“As a tacker, to become a welder I had to take a Journeyman’s Test, and I took that test until I passed it.  Then I went to work welding the seams of the ships.”
White notes that the pictures of the young women seen from those days were accurate as they were portrayed to the public.
“We wore our hair in bandanas, wore high top shoes with steel toes and coveralls.  Our leather coveralls and jacket, hood and gloves was in six lockers at the yard,” she said.
“You’ve seen pictures of women, some famous – some not, dressed in those coveralls and bandanas and that is how we went to work every day.”
Among those famous pictures which have been distributed for years was a young Norma Jeane Mortensen Baker, who parlayed her “15 minutes of fame” as a patriotic riveter into that of a Hollywood starlet.
“You probably know her as Marilyn Monroe,” White quipped, “those pictures helped  get her noticed.”
Those times in the shipyards were hard work White points out and very dangerous.
“We were over water.  I sat on a five-gallon on a scaffold on the outside of the ship, starting on the bottom and finished it.”
Upon completion, those ships had one final shipyard duty before setting sail.
“When the ship was ready to launch, movie stars and big shots would come and hit the ship with champagne to christen it and it was ready to sail.”
White continued, “I saw Lana Turner and Joan Crawford, I can’t remember the others, I didn’t know them as well.”
She also explained that not only was the work difficult, just getting to work proved to be a challenge.
“My husband, J.D. White, was stationed in San Francisco, Calif.  My day started at 5 a.m. during blackout time and there was just very little light shining on the curb of the street, just the street numbers painted there.”
White added, “I caught a streetcar, changed twice, then got on a ferry and rode 21 miles to Richmond (Calif.).  We came so close to Alcatraz Prison you could see the guards and their guns.  We could see San Quentin Prison also.”
She remembers thinking as she passed Alcatraz that “those young men were someone’s sons and brothers and husbands and it was a really somber trip sometimes.”
However, it did not always affect their ferry rides.
“A lot of mornings we would jitterbug on the ferry, we had fun,” she explained with a smile.
Those days in the shipyards were also memorable for another reason for the onetime Beedeville native.
“I worked side by side with men and and made the same money they did.  It was the first and last time I have done that.”
When her husband shipped overseas, White returned to Arkansas and began a very eclectic work history which, in one way or another, often involved modes of transportation.
“I have made shoes, planes, ships and rockets,” she eagerly stated, ” I went to work at a Rocket plant in Camden.  I have also worked in a factory making airplanes as well as Air Research plant in Los Angeles, Calif. after the war.”
As well as making factory products, White notes that “I have also made women beautiful for 46 years with Mary Kay Cosmetics.”
After working for Drs. Omar Weatherford and Conrad Taylor, she worked at one time or another for both hospitals performing duties from Certified Nursing Assistant to switchboard operation, ward clerk and time in the administration office.
White also worked for many years as a caregiver in the Newport area.
“I have sat with doctors, lawyers and so many others I couldn’t name.  But they have touched my life in so many ways and I hope to have touched them also.”  
She continued, “I still get calls to sit with people but I need a housekeeper now.”
Despite her age, White maintains she tries to keep busy as she belongs to a number of local organizations including the Business Professional Women’s Club of which she has served as President as well as District President.  She was also voted their Woman of the Year in 1988 and the Best Community Volunteer in 2004 and 2007.
She has been the President of the American Legion #47 for 38 years and has served as District 6 President.
“I am also a member of the Church of Christ, Senior Circle and the Fifty Five Alive Groups.”
As time marches on, White remains extremely proud of the work she did those many years ago.
“I belong to the American Rosie the Riveter Association (A.R.R.A.), which was founded in 1998 to honor the working women of World War II,” she explained.
Their motto, “We Can Still Do It!” and seems to be something White has lived her whole life by.
Today, White shares her stories with her daughter, Judy Lynn White Rennicke, her granddaughters, Brandy and Jennifer, and two great-grandchildren, Ardin and Sophie, “the loves of my life.”
“It hasn’t been a bad life for an old girl from Beedeville.”
 

Article source: http://www.newportindependent.com/topstories/x2094177280/-Ruthie-the-Welder-does-her-part

27
APR

Hardworking Welder - Classified Ad

Ad #14364675 Contact

Boston Soto

City

Buffalo

Zip

14207

Created

April 25, 2012

Expires

October 25, 2012

Viewed

26 times

Structural Steel & Erector Company is seeking a Hardworking Welder with field experience and shop layout knowledge. Full Time position with benefits and great wages. Send resumes to : ebatlassteel@aol.com

Sending...

Sending...

Avoid scams and fraud

Signs of fraud: wire transfer, money orders, cashier checks, shipping, escrow, "transaction protection," "guarantee." Be safe by dealing locally. Read more

Thursday, April 26, 2012

Electrician, Mason and Welder Jobs in Bahrain | JI71277

Please Note

Careermidway.com is only a place to bring job seekers & employers together. Applicants are advised to investigate the bonafides of the prospective employer by yourself. We do NOT endorse any requests for money payments and strictly advice against sharing personal or bank related information. So we are not responsible for false information, if any.